Daktronics

Tissot Shot Clocks Work Instructions for Installing Daktronics Clear Transparent Shot Clock Horn

Topic

  • How to install the Daktronics transparent/clear Shot Clock Horn to a stanchion with TISSOT Shot Clock.
  • It has been decided to mount the Daktronics horn on the side of the stanchion under the small clock at the back of the stanchion as shown in the picture.

Environment

  • Product Family: Shot Clock
  • Product: Daktronics Horn 0A-1322-0015 & -0332, TISSOT Shot Clocks
  • Component: 
  • Control System: NBA Arenas
 

Steps

  1. Verify the facility has TISSOT high voltage relay box.  This box will be between the Tissot stanchion box and Tissot's 120V buzzer.
  2. Disconnect the current TISSOT buzzer and remove from it's current location.
  3. Route the current TISSOT horn power cable to the new location.
  4. Locate the Daktronics Horn Assemblies.
  5. Remove the 8 screws and open up the horn enclosure
      6. Step 4.jpg
    • Using a pliers pinch the strain relief to remove the cable from the back of the enclosure. Also remove ground wire from the ground terminal.
        • Step 5.jpg
      1. Using the strain relief from the cable removed from the Daktronics horn enclosure secure the TISSOT horn power cable into the back of the Daktronics horn enclosure. This cable is smaller in diameter so using black electrical tape wrap the end of the cable approximately 20 times at the point where the strain relief will grip the cable.
      2. Connect the Green ground wire to the ground terminal.
      3. Cut the terminal off the power wires and strip the insulation back about an inch.
          4. Step 8.jpg
        1. Cut the wires going into the 2 pin connector on the Daktronics horn and then strip the black and white wires back about an inch.
            2. Step 9.jpg
          1. Wire nut the horn wires to the power wires coming into the enclosure. Black to black and white to white. Using electrical tape wrap the wire nuts for added security that will avoid the wire nuts from loosening up.
              2. Step 10.jpg
            1. Re-assemble the horn enclosure with the 8 screws removed earlier.
            2. Mount the horn in the location shown above:
              1. Place horn in desired location with approximately a 20 degree downward slope.
                1. Make sure you mount the horn at least 1" above the bottom of the stanchion in order to give enough clearance for the pads when the stanchion is down.
              2. Mark mounting holes through the holes provided in the mounting bracket on the horn enclosure. 
              3. Using a ¼ - 20 Drill and tap bit drill two mounting holes at the marked locations. 
                1. If desired self tapping screws could be used here as well but this approach would allow for a more secure mount. 
              4. Using corresponding bolts secure the horn to the stanchion. 
                1. Depending on the hardware used you will more than likely need to enlarge the holes on the horn enclosure mounting bracket to accommodate the necessary hole size. 
                Step 12 4.jpg Step 12 4-001.jpg Step 12 4-002.jpg
              1. Secure cable accordingly to the stanchion.
              2. Connect the horn power cable as before and test horn using the TISSOT entry terminal.

              KB ID: DD3508748

              DISCLAIMER: Use of this content may void the equipment warranty, please read the disclaimer prior to performing any service of the equipment.

              DAKTRONICS DOES NOT PROMISE THAT THE CONTENT PROVIDED HEREIN IS ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, OR THAT YOUR USE OF THE CONTENT WILL PROVIDE SPECIFIC RESULTS. THE CONTENT IS DELIVERED ON AN "AS-IS" AND "AS-AVAILABLE" BASIS. ALL INFORMATION PROVIDED IN THIS ARTICLE IS SUBJECT TO CHANGE WITHOUT NOTICE. DAKTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF ACCURACY, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DAKTRONICS DISCLAIMS ANY AND ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF YOU OR ANY THIRD PARTIES IN CONNECTION WITH OR RELATED TO YOUR USE OF THE CONTENT. ADJUSTMENT, REPAIR, OR SERVICE OF THE EQUIPMENT BY ANYONE OTHER THAN DAKTRONICS OR ITS AUTHORIZED REPAIR AGENTS MAY VOID THE EQUIPMENT WARRANTY. YOU ASSUME TOTAL RESPONSIBILITY FOR YOUR USE OF THE CONTENT AND ANY LINKED CONTENT. YOUR SOLE REMEDY AGAINST DAKTRONICS FOR DISSATISFACTION WITH THE CONTENT IS TO STOP USING THE CONTENT. THIS LIMITATION OF RELIEF IS A PART OF THE BARGAIN BETWEEN THE PARTIES.

              The above disclaimer applies to any property damage, equipment failure, liability, infringement, or personal injury claim arising out of or in any way related to your use or application of the content, whether such claim is for breach of contract, tort, negligence or any other cause of action.