Daktronics

How do I setup a DM-100 handheld for a point of sale (POS) system?

Topic

  • How do I setup a DM-100 for a POS system?

Environment

  • Product: Fuelight or DataMaster, FL-3000, Gas Price or Petroleum Price Display
  • Component:
  • Control System: POS interface kit (wired or wireless)

Steps

Note: The DM-100 menus have changed slightly between the different revisions of firmware.  Below has directions for the different menus.  The DD/ED and revision of the DM-100 is displayed on the boot up of the handheld.

  • DM-100 - DD-2256160 (3.0 or higher).
    1. Press MENU on the DM-100 handheld.
    2. Using the arrow buttons, scroll down to DISPLAY MENU and press ENTER.
    3. Using the arrow buttons, scroll to POS SETTINGS and press ENTER.
    4. Using the arrow buttons, scroll to the POS being used and press ENTER.
      • Available options:
        • NONE
        • GENERIC
        • SAPPHIRE
        • AUTOGAS
        • PAM 1000
        • ALLIED
        • GSITE/PASSPORT
    5. The DM-100 will now be prompting to set each Line Product to an appropriate value or price category so once Line 1 Product is set Press Enter to set Line 2 Product and so on.  If the Line is not being used set it to NONE.  The POS system or vendor should be able to provide the details of how to setup each Line.
    6. For newer firmware DM-100's Line Product will look like the following.
      • image.png

 

  • DM-100 - DD-2256160 (2.2 or lower) and ED-13374 (all revisions)
    1. Press MENU on the DM-100 handheld.
    2. Using the arrow buttons, scroll to POS SETTINGS and press ENTER.
    3. Using the arrow buttons, scroll to the POS being used and press ENTER.
      • Available options:
        • NONE
        • GENERIC
        • SAPPHIRE
        • AUTOGAS
        • PAM 1000
        • ALLIED
        • GSITE/PASSPORT
    4. The DM-100 will now be prompting to set each Line Product to an appropriate value or price category so once Line 1 Product is set Press Enter to set Line 2 Product and so on.  If the Line is not being used set it to NONE.  The POS system or vendor should be able to provide the details of how to setup each Line.

KB ID: DD2555112

DISCLAIMER: Use of this content may void the equipment warranty, please read the disclaimer prior to performing any service of the equipment.

DAKTRONICS DOES NOT PROMISE THAT THE CONTENT PROVIDED HEREIN IS ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, OR THAT YOUR USE OF THE CONTENT WILL PROVIDE SPECIFIC RESULTS. THE CONTENT IS DELIVERED ON AN "AS-IS" AND "AS-AVAILABLE" BASIS. ALL INFORMATION PROVIDED IN THIS ARTICLE IS SUBJECT TO CHANGE WITHOUT NOTICE. DAKTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF ACCURACY, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DAKTRONICS DISCLAIMS ANY AND ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF YOU OR ANY THIRD PARTIES IN CONNECTION WITH OR RELATED TO YOUR USE OF THE CONTENT. ADJUSTMENT, REPAIR, OR SERVICE OF THE EQUIPMENT BY ANYONE OTHER THAN DAKTRONICS OR ITS AUTHORIZED REPAIR AGENTS MAY VOID THE EQUIPMENT WARRANTY. YOU ASSUME TOTAL RESPONSIBILITY FOR YOUR USE OF THE CONTENT AND ANY LINKED CONTENT. YOUR SOLE REMEDY AGAINST DAKTRONICS FOR DISSATISFACTION WITH THE CONTENT IS TO STOP USING THE CONTENT. THIS LIMITATION OF RELIEF IS A PART OF THE BARGAIN BETWEEN THE PARTIES.

The above disclaimer applies to any property damage, equipment failure, liability, infringement, or personal injury claim arising out of or in any way related to your use or application of the content, whether such claim is for breach of contract, tort, negligence or any other cause of action.