Vanguard Site Configuration
Topic
- How to define the Option for a Vanguard Display using the Site Configuration document.
Environment
- Product: Vanguard
- Components: VFC, DMP, VFC-3000, VCB, LED Modules, Light sensors, Temp sensors
- Control System: VFC, DMP, VFC-3000
Steps
When configuring Vanguard Display refer to contract Site Configuration document:
SYSTEM CONFIGURATION:
- ACCESS- How you access display whether it be front or rear entry, or you can walk into (Walk-In) the display.
- DISPLAY INTERFACE: Number of VCBs used to create one sign.
- Display interface can also be used to set sign to alias to first sign associated to VCB / VCBs
- MODEL: Display type. VM, VF, VX, DB-5000, DVX, VS6(GS6), VL, VSLS.
- you can refer to assembly number to confirm model.
- VS6 is a spinoff of a GS6 display with the NTCIP application installed.
- MODULE: This is the size, color, pitch, and power type
- PIXEL HEIGHT: How many pixels high the display is.
- PIXEL WIDTH: How many pixels wide the display is.
- TYPE: Full, Line, or Character matrix is based on the data acquisition or how the data is transmitted and received throughout the display.
- WIRING LAYOUT: Wiring of the module are in Rows or in Bays.
PERIPHERAL CONFIGURATION:
- LIGHT SENSOR-Device that detects light to adjust brightness
- AMBIENT-Total available light
- FRONT-Light at the front of the display
- REAR-Light at the rear
- LINE-The most center light
- MDLS-Multi directional light sensor typically used with a PLR
- TEMP SENSOR-Senses Temperature
- EXTERNAL-Temperature reading of outdoors
- INTERNAL-Temperature reading of inside of display
- MODULE-Temperature of module
- HUMIDITY SENSOR-Senses the percentage of moisture in the air
- ISOLATION BOARDS-ISO Board attached to power supply to monitor power
- DC I/O-DC Voltage input and output
- VCB II RETRO-Specified Interface used to communicate to sign
- DOOR SENSOR-Sensor to monitor door (open or closed)
- AIRFLOW SENSOR-Sensor to monitor airflow in sign
- RPM SENSOR-Measure revolutions per minute of fans
- CABINET HEATERS-Warms the cabinet/display
- DEFOG HEATERS-Reduces fog on display face
- FACE FANS-Fans responsible for circulating air inwards
- VENT FANS-Fans responsible for circulating air out
- BEACONS-Lights located on the outside of display
- SURGE SUPPRESSOR-Protect electrical equipment from power surges/spikes
- POWER SYSTEM- Version of power
- GEN IV (DEFAULT)-Default power system
- PSRB-Power supply redundancy board
- ELTEK-Remote power DC system
KB ID: 000027523
DISCLAIMER: Use of this content may void the equipment warranty, please read the disclaimer prior to performing any service of the equipment.
DAKTRONICS DOES NOT PROMISE THAT THE CONTENT PROVIDED HEREIN IS ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, OR THAT YOUR USE OF THE CONTENT WILL PROVIDE SPECIFIC RESULTS. THE CONTENT IS DELIVERED ON AN "AS-IS" AND "AS-AVAILABLE" BASIS. ALL INFORMATION PROVIDED IN THIS ARTICLE IS SUBJECT TO CHANGE WITHOUT NOTICE. DAKTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF ACCURACY, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DAKTRONICS DISCLAIMS ANY AND ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF YOU OR ANY THIRD PARTIES IN CONNECTION WITH OR RELATED TO YOUR USE OF THE CONTENT. ADJUSTMENT, REPAIR, OR SERVICE OF THE EQUIPMENT BY ANYONE OTHER THAN DAKTRONICS OR ITS AUTHORIZED REPAIR AGENTS MAY VOID THE EQUIPMENT WARRANTY. YOU ASSUME TOTAL RESPONSIBILITY FOR YOUR USE OF THE CONTENT AND ANY LINKED CONTENT. YOUR SOLE REMEDY AGAINST DAKTRONICS FOR DISSATISFACTION WITH THE CONTENT IS TO STOP USING THE CONTENT. THIS LIMITATION OF RELIEF IS A PART OF THE BARGAIN BETWEEN THE PARTIES.
The above disclaimer applies to any property damage, equipment failure, liability, infringement, or personal injury claim arising out of or in any way related to your use or application of the content, whether such claim is for breach of contract, tort, negligence or any other cause of action.