Daktronics

How to sync time and date on the VFC's DMP board and VIP board using the webpage interface or locally at the controller

Topic

  • How do I check that the time is set correctly?
  • The message isnt showing on the sign, but the controller says it is.
  • Daylight savings changed and the peripherals are timing out or not reporting correctly.

Environment

  • VFC
    • DMP-5050
    • VIP-5050

Steps

REMOTLEY USING THE WEBPAGE INTERFACE:
  1. Establish a secure ethernet connection to the VFC controller.
  2. Log into the web configuration for the DMP board by entering the IP address of the display followed by :80 into the address bar of a web browser. Example. 10.10.10.10:80
  3. You will be prompted for a password.
  4. Click Configuration in the left column.
  5. Click on Time on the next screen that comes up.
  6. Set the Time zone for where the controller is currently at.
  7. Sync date and time by clicking on the Sync button.
  8. last step is to click on the Save button in the upper left corner.
  9. Log into the web configuration for the VIP board by entering the IP address of the display followed by :85 into the address bar of a web browser. Example. 10.10.10.10:85
  10. You will be prompted for a password.
  11. Click Configuration in the left column.
  12. Click on time on the next screen that come sup.
  13. Set the Time zone for where the controller is currently at.
  14. Set the current date & current time by clicking on Synchronize button.
  15. last step is to click on the Save button in the upper left corner.

LOCALLY USING THE CONTROLLER MENU SCREEN:
  1. Log into the controller.
  2. Press enter on the keypad.
  3. Select Shared.
  4. Select Time.
  5. Select Set Time.
  6. Choose your time zone.
  7. Select correct DST option.
  8. Select the right Month.
  9. Select the right Day.
  10. Select the right year.
  11. Select the right hour.
  12. Select the right Minute.
  13. Select the right Seconds.
  14. Set NTP if the customer is using this option. This is set to Disabled by default.
  15. Cancel back to the Shared Operations screen.
  16. Select Reset.
  17. Select Reboot, this will do a "soft reset" on the controller.

KB ID: 000023864

DISCLAIMER: Use of this content may void the equipment warranty, please read the disclaimer prior to performing any service of the equipment.

DAKTRONICS DOES NOT PROMISE THAT THE CONTENT PROVIDED HEREIN IS ERROR-FREE OR THAT ANY DEFECTS WILL BE CORRECTED, OR THAT YOUR USE OF THE CONTENT WILL PROVIDE SPECIFIC RESULTS. THE CONTENT IS DELIVERED ON AN "AS-IS" AND "AS-AVAILABLE" BASIS. ALL INFORMATION PROVIDED IN THIS ARTICLE IS SUBJECT TO CHANGE WITHOUT NOTICE. DAKTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF ACCURACY, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DAKTRONICS DISCLAIMS ANY AND ALL LIABILITY FOR THE ACTS, OMISSIONS AND CONDUCT OF YOU OR ANY THIRD PARTIES IN CONNECTION WITH OR RELATED TO YOUR USE OF THE CONTENT. ADJUSTMENT, REPAIR, OR SERVICE OF THE EQUIPMENT BY ANYONE OTHER THAN DAKTRONICS OR ITS AUTHORIZED REPAIR AGENTS MAY VOID THE EQUIPMENT WARRANTY. YOU ASSUME TOTAL RESPONSIBILITY FOR YOUR USE OF THE CONTENT AND ANY LINKED CONTENT. YOUR SOLE REMEDY AGAINST DAKTRONICS FOR DISSATISFACTION WITH THE CONTENT IS TO STOP USING THE CONTENT. THIS LIMITATION OF RELIEF IS A PART OF THE BARGAIN BETWEEN THE PARTIES.

The above disclaimer applies to any property damage, equipment failure, liability, infringement, or personal injury claim arising out of or in any way related to your use or application of the content, whether such claim is for breach of contract, tort, negligence or any other cause of action.